[ tvtime-Bugs-929163 ] How about PAL-DK in TVTIME? I need it.

Bugs item #929163, was opened at 2004-04-04 05:46
Message generated for change (Comment added) made by vektor
You can respond by visiting: 
https://sourceforge.net/tracker/?func=detail&atid=506987&aid=929163&group_id=64301

Category: Capture and tuner related
Group: Open bugs in CVS tvtime
Status: Open
Resolution: None
>Priority: 9
Submitted By: Nobody/Anonymous (nobody)
Assigned to: Billy Biggs (vektor)
Summary: How about PAL-DK in TVTIME? I need it.

Initial Comment:
Hi, here is problem, I am using PCTV on archlinux.
On PAL I can see picture, but sound is bbszzzzz

On windows the same with PAL.
But there is PAL-DK and it work fine.

But in tvtime i did not find PAL-DK.


M.

----------------------------------------------------------------------

>Comment By: Billy Biggs (vektor)
Date: 2004-06-24 21:06

Message:
Logged In: YES 
user_id=153320

I am still not sure what to do about this bug.  I think we
need to at least understand what's going on before 0.9.13. 
Marking this as high priority.

----------------------------------------------------------------------

Comment By: Nobody/Anonymous (nobody)
Date: 2004-04-11 12:24

Message:
Logged In: NO 

Well, I don't know I have MSI TV@nywhere Master (MS8606),
it's NTSC/PAL/SECAM 
cx23881-27 based tv-card.
In modprobe I've tried lots of parameters, but in dmesg I
always see 
NTSC+BTSC, I should use PAL D/K, with A2 or NICAM audio...
As far as I know xawtv sets PAL to PAL D/K and Audio to A2
while switching 
between channels (I've seen it in dmesg), but it does not
make my sound work 
anyway (probably v4l driver in version 0.0.3 is not quite
ready yet, or there 
is some other problem...)

Here is how I modprobe:

# modprobe tda9887 pal=d
# modprobe tuner type=33 pal=d
# modprobe cx8800 audio_debug=1 video_debug=1 nicam=1

and matching part of dmesg:

Linux video capture interface: v1.00
cx2388x v4l2 driver version 0.0.3 loaded
cx8800[0]: found at 0000:00:07.0, rev: 3, irq: 10, latency:
64, mmio: 
0xde000000
cx8800[0]: subsystem: 1462:8606, board: MSI TV-@nywhere Master 
[card=7,autodetected]
cx8800[0]: cx8800_reset
cx8800[0]: i2c attach [client=eeprom]
tda9885/6/7: chip found @ 0x86
cx8800[0]: i2c attach [client=tda9887]
tuner: chip found at addr 0xc2 i2c-bus cx8800[0]
tuner: type set to 33 (MT20xx universal) by cx8800[0]
tuner: microtune: companycode=3cbf part=42 rev=21
tuner: microtune MT2050 found, OK
cx8800[0]: i2c attach [client=MT20xx universal]
tuner: The type=<n> insmod option will go away soon.
tuner: Please use the tuner=<n> option provided by
tuner: tv aard core driver (bttv, saa7134, ...) instead.
cx8800[0]: i2c register ok
cx8800[0]: registered device video0 [v4l2]
cx8800[0]: registered device vbi0
cx8800[0]: set_control id=0x980909 reg=0x320594 val=0x40
[shadowed]
cx8800[0]: set_control id=0x980905 reg=0x320594 val=0x0
[shadowed]
cx8800[0]: set_tvnorm: "NTSC-M" fsc8=28636360 adc=28636363
vdec=28636360
cx8800[0]: set_pll:    MO_PLL_REG       0x00fffffe 
[old=0x013d14c6,freq=28636360]
cx8800[0]: pll locked [pre=2,ofreq=28636360]
cx8800[0]: set_tvnorm: MO_INPUT_FORMAT  0x00000001
[old=0x00000007]
cx8800[0]: set_tvnorm: MO_OUTPUT_FORMAT 0x181f0008
[old=0x181f0008]
cx8800[0]: set_tvnorm: MO_SCONV_REG     0x00020000
[old=0x00019d5e]
cx8800[0]: set_tvnorm: MO_SUB_STEP      0x00400000
[old=0x00400000]
cx8800[0]: set_tvnorm: MO_SUB_STEP_DR   0x004ec7ed
[old=0x003f9adc]
cx8800[0]: set_tvnorm: MO_AGC_BURST     0x00007270 
[old=0x00008887,bdelay=114,agcdelay=112]
cx8800[0]: set_tvnorm: MO_HTOTAL        0x0000138e
[old=0x00001c6f,htotal=910]
cx8800[0]: set_audio_standard_BTSC (status: unknown)
cx8800[0]: video_mux: 0 [vmux=0,gpio=0x0,0x0,0x0,0x0]


Michal

----------------------------------------------------------------------

Comment By: Billy Biggs (vektor)
Date: 2004-04-11 09:37

Message:
Logged In: YES 
user_id=153320

The difference between PAL-DK and the default PAL-BG is the
audio carrier.  It's at 6.5 MHz with PAL-D and 5.5 MHz with
PAL-BG.  

Usually, the tuner hardware on your capture card is able to
auto-detect this.  If this fails, there is a module
parameter for the tuner module to change the standard.

Add:

options tuner pal=d

Or use:

modprobe tuner pal=d

To force your tuner into PAL-DK mode.  This is not something
(as far as I know) that we can control in tvtime.

----------------------------------------------------------------------

You can respond by visiting: 
https://sourceforge.net/tracker/?func=detail&atid=506987&aid=929163&group_id=64301


-------------------------------------------------------
This SF.Net email sponsored by Black Hat Briefings & Training.
Attend Black Hat Briefings & Training, Las Vegas July 24-29 - 
digital self defense, top technical experts, no vendor pitches, 
unmatched networking opportunities. Visit www.blackhat.com