Re: Re[2]: Multiple IP on WAN

I'm not quite clear, is this what you are looking for

Give the WAN the public IP address you want for LAN access
Give the LAN NIC the 10.0.0.1 IP address
Set up DHCP
Use DHCP to give static IP addresses to machine you want to be addresses 
from the WAN
Create a number of vlans with your additional public IP addresses on the 
WAN.
1:1 mapp from the vlans on the external interface to the required an 
internal machines
or port foward for the sevices you want to expose on each machine from the 
appropreate vlan

--Robert

> Hiya, nope didn't work.. (Im using RC2)
>
> Basically here is my setup.
>
> 8 public ips from my isp.
>
> I share my home internet with 10.0.0.0/8 range and some of these
> public ips on other machines.
>
> I would like the router to have
>
> 10.0.0.1 and my-public-ip-1
>
>
> Then my other workstations/servers that have real public ips use
> my-public-ip-1 as the default gateway and use their own public ips
> ok
>
> Then workstations without real public ips, then they just route using
> the 10.0.0 range and use the public ip on that router.
>
> I've tried no end of combinations to get it working. The virtual ips
> dont work properly (ie.. cannot ping that ip).. The only thing I can
> do is assign virtual ip and do advanced outbound nat for vhosts.
>
> You know the WAN interface? I would like to have multiple ips there.
>
> ** exactly like ifconfig and adding an alias.
>
> The only ways I can see on pfsense is 1) do the alias manually in
> shell or 2) add another NIC. But the NIC would cause a loop in the
> network. :(
>
> Thanks,
> Chris
>
> ===8<==============Original message text===============
> > You can add additional IPs at firewall>Virtual IP. After you added
> > them there you can use these for NAT. Make sure you add appropriate
> > firewallrules for this additional traffic (let them autocreate when
> > using protforwarding, it sets up the right rules for you).
>
> > Holger
>
> > > -----Original Message-----
> > > From: Robert Mortimer [mailto:rmortimer@xxxxxxxxxxxxxxxxxxxxxxxx]
> > > Sent: Friday, August 18, 2006 10:55 PM
> > > To: discussion@xxxxxxxxxxx
> > > Subject: Re: [pfSense-discussion] Multiple IP on WAN
> > >
> > >
> > > Try
> > >
> > > Interfaces > Assign > VLAN
> > >
> > > I think this is what you want
> > >
> > > ---Robert
> > >
> > > ----- Original Message ----- 
> > > From: "Chris Noble" <chrisn@xxxxxxxxx>
> > > To: <discussion@xxxxxxxxxxx>
> > > Sent: Friday, August 18, 2006 7:27 PM
> > > Subject: [pfSense-discussion] Multiple IP on WAN
> > >
> > >
> > > >
> > > > Hi there,
> > > >
> > > > I have 8 ips with my isp and would like to use PPPoE on my
> > > > linksys router.. I can do this but for 1 ip.
> > > >
> > > > Is there anywhere that I can set a local ip eg 10.0.0.1/8 and then
> > > > my isp ip range which is say 123.123.123.1/29. One IP is a dedicated
> > > > router IP and I would like that ip on the pfsense router. It can be
> > > > done manually if I ssh into the machine, but cannot find anywhere to
> > > > add another ip to the WAN interface.
> > > >
> > > > I hope I explained it clearly.
> > > >
> > > > Any ideas?
> > > >
> > > > Many thanks,
> > > > Chris
> > > >
> > > >
>
>
> ===8<===========End of original message text===========