I would like to know if anyone has been able to get NICs that use the
em(4) driver working on OpenBSD 3.4 or 3.5. I have experienced problems
with Intel PRO/1000XT NICs on both a XP1000 and a DS20. The XP1000 is
currently running OBSD 3.2 since that was the last version to work
properly on the hardware. The problems with the XP1000 are outlined at:
http://marc.theaimsgroup.com/?l=openbsd-alpha&m=107826670310083&w=2
3.5 runs fine on the DS20 provided the Intel NIC is not configured. If the
Intel NIC is assigned an IP, the machine becomes completely unresponsive
and must be rebooted. Below is the dmesg for the DS20. The reason the DS20
is not running GENERIC is that GENERIC won't boot, as outlined at:
http://marc.theaimsgroup.com/?l=openbsd-alpha&m=107829056900509&w=2
The only difference between the running kernel and GENERIC is the line:
config bsd root on sd0a swap on sd0b
If anyone has any advice on how to get the em driver working, it would be
greatly appreciated.
Thanks,
-- Mark Roberts
dmesg of DS20:
[ using 525896 bytes of bsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2004 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 3.5 (GIBBS) #0: Sun Dec 1 06:25:52 EST 2002
root@xxxxxxxxxxxxxxxxxxxxx:/usr/src/sys/arch/alpha/compile/GIBBS
AlphaServer DS20 500 MHz
8192 byte page size, 1 processor.
total memory = 536870912 (524288K)
(2654208 reserved for PROM, 534216704 used by OpenBSD)
avail memory = 461996032 (451168K)
using 6521 buffers containing 53420032 bytes (52168K) of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21264-4 (pass 3)
cpu0: Architecture extensions: 303<PAT,MVI,FIX,BWX>
tsc0 at mainbus0: 21272 Core Logic Chipset, Cchip rev 0
tsc0: 8 Dchips, 2 memory buses of 32 bytes
tsc0: arrays present: 512MB, 0MB, 0MB, 0MB, Dchip 0 rev 1
tsp0 at tsc0
pci0 at tsp0 bus 0
sio0 at pci0 dev 5 function 0 "Contaq Microsystems CY82C693U ISA" rev 0x00
pciide0 at pci0 dev 5 function 1 "Contaq Microsystems CY82C693U ISA" rev
0x00: DMA, channel 0 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <Maxtor 84320D5>
wd0: 16-sector PIO, LBA, 4119MB, 8437500 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide1 at pci0 dev 5 function 2 "Contaq Microsystems CY82C693U ISA" rev
0x00: no DMA, channel 0 wired to compatibility
pciide1: channel 0 disabled (no drives)
"Contaq Microsystems CY82C693U ISA" rev 0x00 at pci0 dev 5 function 3 not
configured
vga0 at pci0 dev 7 function 0 "Texas Instruments 3DLabs Permedia 2" rev
0x01
wsdisplay0 at vga0: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
em0 at pci0 dev 8 function 0 "Intel PRO/1000XT (PWLA8490XT)" rev 0x02: dec
6600 irq 27, address: 00:02:b3:ed:28:2a
isa0 at sio0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
midi0 at pcppi0: <PC speaker>
isabeep0 at pcppi0
lpt0 at isa0 port 0x3bc/4 irq 7
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70/2: mc146818 or compatible
tsp1 at tsc0
pci1 at tsp1 bus 0
ppb0 at pci1 dev 7 function 0 "DEC 21152 PCI-PCI" rev 0x03
pci2 at ppb0 bus 2
siop0 at pci2 dev 0 function 0 "Symbios Logic 53c875" rev 0x04: dec 6600
irq 47, using 4K of on-board RAM
scsibus0 at siop0: 16 targets
siop0: target 5 now using 8 bit 10.0 MHz 16 REQ/ACK offset xfers
cd0 at scsibus0 targ 5 lun 0: <DEC, RRD47 (C) DEC, 1206> SCSI2 5/cdrom
removable
siop1 at pci2 dev 1 function 0 "Symbios Logic 53c875" rev 0x04: dec 6600
irq 46, using 4K of on-board RAM
scsibus1 at siop1: 16 targets
siop1: target 0 now using tagged 16 bit 20.0 MHz 15 REQ/ACK offset xfers
sd0 at scsibus1 targ 0 lun 0: <DEC, RZ2DD-LS (C) DEC, 0306> SCSI2 0/direct
fixed
sd0: 8678MB, 5273 cyl, 20 head, 168 sec, 512 bytes/sec, 17773524 sec total
siop1: target 1 now using tagged 16 bit 20.0 MHz 15 REQ/ACK offset xfers
sd1 at scsibus1 targ 1 lun 0: <DEC, RZ2ED-LS (C) DEC, 0306> SCSI2 0/direct
fixed
sd1: 17365MB, 7001 cyl, 20 head, 254 sec, 512 bytes/sec, 35565080 sec
total
siop1: target 2 now using tagged 16 bit 20.0 MHz 15 REQ/ACK offset xfers
sd2 at scsibus1 targ 2 lun 0: <DEC, RZ2ED-LS (C) DEC, 0306> SCSI2 0/direct
fixed
sd2: 17365MB, 7001 cyl, 20 head, 254 sec, 512 bytes/sec, 35565080 sec
total
siop1: target 3 now using tagged 16 bit 20.0 MHz 15 REQ/ACK offset xfers
sd3 at scsibus1 targ 3 lun 0: <DEC, RZ2ED-LS (C) DEC, 0306> SCSI2 0/direct
fixed
sd3: 17365MB, 7001 cyl, 20 head, 254 sec, 512 bytes/sec, 35565080 sec
total
siop1: target 4 now using tagged 16 bit 20.0 MHz 15 REQ/ACK offset xfers
sd4 at scsibus1 targ 4 lun 0: <DEC, RZ2ED-LS (C) DEC, 0306> SCSI2 0/direct
fixed
sd4: 17365MB, 7001 cyl, 20 head, 254 sec, 512 bytes/sec, 35565080 sec
total
de0 at pci2 dev 2 function 0 "DEC 21140" rev 0x22: dec 6600 irq 45
de0: 21140A [10-100Mb/s] pass 2.2 address 00:06:2b:00:a4:19
isp0 at pci1 dev 8 function 0 "QLogic ISP1020" rev 0x05: dec 6600 irq 43
scsibus2 at isp0: 16 targets
isp1 at pci1 dev 9 function 0 "QLogic ISP1020" rev 0x05: dec 6600 irq 39
scsibus3 at isp1: 16 targets
stray isa irq 3
stray isa irq 4
WARNING: can't figure what device matches ""
rootdev=0x800 rrootdev=0x800 rawdev=0x802
WARNING: / was not properly unmounted
de0: enabling Full Duplex 100baseTX port
stray isa irq 4
stray isa irq 3
de0: enabling 100baseTX port
--------------------------------
Mark Roberts
mark@xxxxxxxxxxxxxxx
Applied Mathematics Research Lab
University of Akron
Systems Administrator
|
