SD card error with RamDisk Rescue

Hi,

I have finally gotten an SD card (SanDisk Ultra II, 2 GB) and I have
tried to install Familiar with RamDisk Rescue but the card does not
work under Linux (it works perfectly with WinCE), this is part of dmesg
that I have have with ssh:

......................................................................
 = 13) is a STUART
pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 0) is a HWUART
RAMDISK driver initialized: 3 RAM disks of 12288K size 1024 blocksize
loop: loaded (max 8 devices)
Battery interface for iPAQ h2200 series - (c) 2004 Szabolcs Gyurko
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with
idebus=xx NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung
NAND 32MiB 3,3V 8-bit) Scanning device for bad blocks
Bad eraseblock 62 at 0x000f8000
Bad eraseblock 673 at 0x00a84000
Bad eraseblock 1244 at 0x01370000
Bad eraseblock 1590 at 0x018d8000
Bad eraseblock 1985 at 0x01f04000
cmdlinepart partition parsing not available
Using builtin partition definition
Creating 4 MTD partitions on "NAND 32MiB 3,3V 8-bit":
0x00000000-0x00004000 : "HTC first-stage bootstrap"
0x00004000-0x00028000 : "HTC rescue bootloader"
0x00028000-0x00168000 : "second-stage loader"
0x00168000-0x02000000 : "root fs"
pxa2xx_udc: version 4-May-2005
usb0: Ethernet Gadget, version: May Day 2005
usb0: using pxa2xx_udc, OUT ep2out-bulk IN ep1in-bulk
usb0: MAC 0e:4b:a0:9b:c7:a8
input: h2200 buttons as /class/input/input1
i2c /dev entries driver
I2C: i2c-0: PXA I2C adapter
Driver for 1-wire Dallas network protocol.
SAMCOP 1-Wire busmaster driver - (c) 2004 Szabolcs Gyurko
1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005,
Szabolcs Gyurko dmabounce: registered device samcop sdi on platform bus
samcop sdi: probe: irq=124 irq_cd=31 dma=0.
samcop sdi: initialisation done.
Console: switching to colour frame buffer device 60x53
MediaQ 1188 chip detected, base IRQ 130
Registered led device: number=power, color=amber
Registered led device: number=notify, color=green
Registered led device: number=bluetooth, color=blue
Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07
13:30:21 2005 UTC). PXA2xx i2Sound: h2200 Audio activated
ALSA device list:
  #0: iPAQ h2200 Audio [codec Philips UDA1380]
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
usb0: full speed config #1: 100 mA, Ethernet Gadget, using CDC Ethernet
Subset mmc0: host does not support reading read-only switch. assuming
write-enable. mmcblk0: mmc0:1432 SD02G 1985024KiB 
 mmcblk0:<3>mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on device mmcblk0, logical block 0
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on device mmcblk0, logical block 0
 unable to read partition table
RAMDISK: Compressed image found at block 0
usb0: full speed config #1: 100 mA, Ethernet Gadget, using CDC Ethernet
Subset VFS: Mounted root (ext2 filesystem).
Freeing init memory: 84K
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on device mmcblk0, logical block 0
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 8
Buffer I/O error on device mmcblk0, logical block 1
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 16
Buffer I/O error on device mmcblk0, logical block 2
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 24
Buffer I/O error on device mmcblk0, logical block 3
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 32
Buffer I/O error on device mmcblk0, logical block 4
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 40
Buffer I/O error on device mmcblk0, logical block 5
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 48
Buffer I/O error on device mmcblk0, logical block 6
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 56
Buffer I/O error on device mmcblk0, logical block 7
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on device mmcblk0, logical block 0
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on device mmcblk0, logical block 0
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 0
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 0
mmcblk0: error 2 transferring data
end_request: I/O error, dev mmcblk0, sector 0
.....................................................
.....................................................


Now, I do not have a card reader, so what can i do?


Thank and sorry for my English