Update the initialization code in the various PCI incarnations of the
orinoco driver. This applies similar initialization and shutdown
cleanups to the orinoco_pci, orinoco_plx and orinoco_tmd drivers. It
also adds COR reset support to the orinoco_plx and orinoco_tmd
drivers, improves PCI power management support in the orinoco_pci
driver and adds a couple of extra supported cards to the ID tables.
Signed-off-by: David Gibson
<hermes-xT8FGy+AXnRB3Ne2BGzF6laj5H9X9Tb+@xxxxxxxxxxxxxxxx>
Index: working-2.6/drivers/net/wireless/orinoco_pci.c
===================================================================
--- working-2.6.orig/drivers/net/wireless/orinoco_pci.c 2005-01-12
15:47:48.215477920 +1100
+++ working-2.6/drivers/net/wireless/orinoco_pci.c 2005-01-12
16:10:57.324301280 +1100
@@ -129,6 +129,11 @@
#define HERMES_PCI_COR_OFFT (500) /* ms */
#define HERMES_PCI_COR_BUSYT (500) /* ms */
+/* Orinoco PCI specific data */
+struct orinoco_pci_card {
+ void __iomem *pci_ioaddr;
+};
+
/*
* Do a soft reset of the PCI card using the Configuration Option Register
* We need this to get going...
@@ -164,8 +169,9 @@
mdelay(1);
reg = hermes_read_regn(hw, CMD);
}
- /* Did we timeout ? */
- if(time_after_eq(jiffies, timeout)) {
+
+ /* Still busy? */
+ if (reg & HERMES_CMD_BUSY) {
printk(KERN_ERR PFX "Busy timeout\n");
return -ETIMEDOUT;
}
@@ -184,6 +190,7 @@
u16 __iomem *pci_ioaddr = NULL;
unsigned long pci_iolen;
struct orinoco_private *priv = NULL;
+ struct orinoco_pci_card *card;
struct net_device *dev = NULL;
err = pci_enable_device(pdev);
@@ -192,24 +199,31 @@
return err;
}
+ err = pci_request_regions(pdev, DRIVER_NAME);
+ if (err != 0) {
+ printk(KERN_ERR PFX "Cannot obtain PCI resources\n");
+ goto fail_resources;
+ }
+
/* Resource 0 is mapped to the hermes registers */
pci_iorange = pci_resource_start(pdev, 0);
pci_iolen = pci_resource_len(pdev, 0);
pci_ioaddr = ioremap(pci_iorange, pci_iolen);
- if (! pci_iorange) {
+ if (!pci_iorange) {
printk(KERN_ERR PFX "Cannot remap hardware registers\n");
- goto fail;
+ goto fail_map;
}
/* Allocate network device */
- dev = alloc_orinocodev(0, NULL);
+ dev = alloc_orinocodev(sizeof(*card), orinoco_pci_cor_reset);
if (! dev) {
err = -ENOMEM;
- goto fail;
+ goto fail_alloc;
}
priv = netdev_priv(dev);
- dev->base_addr = (unsigned long) pci_ioaddr;
+ card = priv->card;
+ card->pci_ioaddr = pci_ioaddr;
dev->mem_start = pci_iorange;
dev->mem_end = pci_iorange + pci_iolen - 1;
SET_MODULE_OWNER(dev);
@@ -226,14 +240,14 @@
if (err) {
printk(KERN_ERR PFX "Cannot allocate IRQ %d\n", pdev->irq);
err = -EBUSY;
- goto fail;
+ goto fail_irq;
}
dev->irq = pdev->irq;
/* Perform a COR reset to start the card */
- if(orinoco_pci_cor_reset(priv) != 0) {
+ err = orinoco_pci_cor_reset(priv);
+ if (err) {
printk(KERN_ERR PFX "Initial reset failed\n");
- err = -ETIMEDOUT;
goto fail;
}
@@ -250,16 +264,19 @@
return 0;
fail:
- if (dev) {
- if (dev->irq)
- free_irq(dev->irq, dev);
+ free_irq(pdev->irq, dev);
- free_orinocodev(dev);
- }
+ fail_irq:
+ pci_set_drvdata(pdev, NULL);
+ free_orinocodev(dev);
+
+ fail_alloc:
+ iounmap(pci_ioaddr);
- if (pci_ioaddr)
- iounmap(pci_ioaddr);
+ fail_map:
+ pci_release_regions(pdev);
+ fail_resources:
pci_disable_device(pdev);
return err;
@@ -269,18 +286,14 @@
{
struct net_device *dev = pci_get_drvdata(pdev);
struct orinoco_private *priv = netdev_priv(dev);
+ struct orinoco_pci_card *card = priv->card;
unregister_netdev(dev);
-
- if (dev->irq)
- free_irq(dev->irq, dev);
-
- if (priv->hw.iobase)
- iounmap(priv->hw.iobase);
-
+ free_irq(dev->irq, dev);
pci_set_drvdata(pdev, NULL);
free_orinocodev(dev);
-
+ iounmap(card->pci_ioaddr);
+ pci_release_regions(pdev);
pci_disable_device(pdev);
}
@@ -312,6 +325,9 @@
orinoco_unlock(priv, &flags);
+ pci_save_state(pdev);
+ pci_set_power_state(pdev, 3);
+
return 0;
}
@@ -324,6 +340,9 @@
printk(KERN_DEBUG "%s: Orinoco-PCI waking up\n", dev->name);
+ pci_set_power_state(pdev, 0);
+ pci_restore_state(pdev);
+
err = orinoco_reinit_firmware(dev);
if (err) {
printk(KERN_ERR "%s: Error %d re-initializing firmware on
orinoco_pci_resume()\n",
@@ -354,6 +373,8 @@
{0x1260, 0x3872, PCI_ANY_ID, PCI_ANY_ID,},
/* Intersil Prism 2.5 */
{0x1260, 0x3873, PCI_ANY_ID, PCI_ANY_ID,},
+ /* Samsung MagicLAN SWL-2210P */
+ {0x167d, 0xa000, PCI_ANY_ID, PCI_ANY_ID,},
{0,},
};
Index: working-2.6/drivers/net/wireless/orinoco_plx.c
===================================================================
--- working-2.6.orig/drivers/net/wireless/orinoco_plx.c 2005-01-12
15:47:48.216477768 +1100
+++ working-2.6/drivers/net/wireless/orinoco_plx.c 2004-11-05
14:20:30.000000000 +1100
@@ -142,26 +142,68 @@
#include "hermes.h"
#include "orinoco.h"
-#define COR_OFFSET (0x3e0/2) /* COR attribute offset of Prism2 PC card */
+#define COR_OFFSET (0x3e0) /* COR attribute offset of Prism2 PC card */
#define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA) /* Enable PC card with
interrupt in level trigger */
+#define COR_RESET (0x80) /* reset bit in the COR register */
+#define PLX_RESET_TIME (500) /* milliseconds */
#define PLX_INTCSR 0x4c /* Interrupt Control & Status Register */
#define PLX_INTCSR_INTEN (1<<6) /* Interrupt Enable bit */
-static const u16 cis_magic[] = {
- 0x0001, 0x0003, 0x0000, 0x0000, 0x00ff, 0x0017, 0x0004, 0x0067
+static const u8 cis_magic[] = {
+ 0x01, 0x03, 0x00, 0x00, 0xff, 0x17, 0x04, 0x67
};
+/* Orinoco PLX specific data */
+struct orinoco_plx_card {
+ void __iomem *attr_mem;
+};
+
+/*
+ * Do a soft reset of the card using the Configuration Option Register
+ */
+static int orinoco_plx_cor_reset(struct orinoco_private *priv)
+{
+ hermes_t *hw = &priv->hw;
+ struct orinoco_plx_card *card = priv->card;
+ u8 __iomem *attr_mem = card->attr_mem;
+ unsigned long timeout;
+ u16 reg;
+
+ writeb(COR_VALUE | COR_RESET, attr_mem + COR_OFFSET);
+ mdelay(1);
+
+ writeb(COR_VALUE, attr_mem + COR_OFFSET);
+ mdelay(1);
+
+ /* Just in case, wait more until the card is no longer busy */
+ timeout = jiffies + (PLX_RESET_TIME * HZ / 1000);
+ reg = hermes_read_regn(hw, CMD);
+ while (time_before(jiffies, timeout) && (reg & HERMES_CMD_BUSY)) {
+ mdelay(1);
+ reg = hermes_read_regn(hw, CMD);
+ }
+
+ /* Did we timeout ? */
+ if (reg & HERMES_CMD_BUSY) {
+ printk(KERN_ERR PFX "Busy timeout\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+
static int orinoco_plx_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
int err = 0;
- u16 __iomem *attr_mem = NULL;
- u32 reg, addr;
+ u8 __iomem *attr_mem = NULL;
+ u32 csr_reg, plx_addr;
struct orinoco_private *priv = NULL;
+ struct orinoco_plx_card *card;
unsigned long pccard_ioaddr = 0;
unsigned long pccard_iolen = 0;
- u16 magic[8];
struct net_device *dev = NULL;
void __iomem *mem;
int i;
@@ -169,78 +211,38 @@
err = pci_enable_device(pdev);
if (err) {
printk(KERN_ERR PFX "Cannot enable PCI device\n");
- return -EIO;
+ return err;
}
- /* Resource 2 is mapped to the PCMCIA space */
- attr_mem = ioremap(pci_resource_start(pdev, 2), PAGE_SIZE);
- if (!attr_mem)
+ err = pci_request_regions(pdev, DRIVER_NAME);
+ if (err != 0) {
+ printk(KERN_ERR PFX "Cannot obtain PCI resources\n");
goto fail_resources;
-
- printk(KERN_DEBUG PFX "CIS: ");
- for (i = 0; i < 16; i++) {
- printk("%02X:", readw(attr_mem+i));
}
- printk("\n");
-
- /* Verify whether PC card is present */
- /* FIXME: we probably need to be smarted about this */
- memcpy_fromio(magic, attr_mem, 16);
- if (memcmp(magic, cis_magic, 16) != 0) {
- printk(KERN_ERR PFX "The CIS value of Prism2 PC "
- "card is unexpected\n");
- err = -EIO;
- iounmap(attr_mem);
- goto fail_resources;
- }
-
- /* PCMCIA COR is the first byte following CIS: this write should
- * enable I/O mode and select level-triggered interrupts */
- writew(COR_VALUE, attr_mem + COR_OFFSET);
- mdelay(1);
- reg = readw(attr_mem + COR_OFFSET);
- iounmap(attr_mem);
- if (reg != COR_VALUE) {
- printk(KERN_ERR PFX "Error setting COR value (reg=%x)\n", reg);
- goto fail_resources;
- }
+ /* Resource 1 is mapped to PLX-specific registers */
+ plx_addr = pci_resource_start(pdev, 1);
- /* bjoern: We need to tell the card to enable interrupts, in
- case the serial eprom didn't do this already. See the
- PLX9052 data book, p8-1 and 8-24 for reference. */
- addr = pci_resource_start(pdev, 1);
- reg = inl(addr+PLX_INTCSR);
- if (reg & PLX_INTCSR_INTEN)
- printk(KERN_DEBUG PFX "Local Interrupt already enabled\n");
- else {
- reg |= PLX_INTCSR_INTEN;
- outl(reg, addr+PLX_INTCSR);
- reg = inl(addr+PLX_INTCSR);
- if(!(reg & PLX_INTCSR_INTEN)) {
- printk(KERN_ERR PFX "Couldn't enable Local
Interrupts\n");
- goto fail_resources;
- }
+ /* Resource 2 is mapped to the PCMCIA attribute memory */
+ attr_mem = ioremap(pci_resource_start(pdev, 2),
+ pci_resource_len(pdev, 2));
+ if (!attr_mem) {
+ printk(KERN_ERR PFX "Cannot remap PCMCIA space\n");
+ goto fail_map_attr;
}
/* Resource 3 is mapped to the PCMCIA I/O address space */
pccard_ioaddr = pci_resource_start(pdev, 3);
pccard_iolen = pci_resource_len(pdev, 3);
- if (! request_region(pccard_ioaddr, pccard_iolen, DRIVER_NAME)) {
- printk(KERN_ERR PFX "I/O resource 0x%lx @ 0x%lx busy\n",
- pccard_iolen, pccard_ioaddr);
- err = -EBUSY;
- goto fail_resources;
- }
mem = pci_iomap(pdev, 3, 0);
if (!mem) {
err = -ENOMEM;
- goto fail_map;
+ goto fail_map_io;
}
/* Allocate network device */
- dev = alloc_orinocodev(0, NULL);
+ dev = alloc_orinocodev(sizeof(*card), orinoco_plx_cor_reset);
if (!dev) {
printk(KERN_ERR PFX "Cannot allocate network device\n");
err = -ENOMEM;
@@ -248,6 +250,8 @@
}
priv = netdev_priv(dev);
+ card = priv->card;
+ card->attr_mem = attr_mem;
dev->base_addr = pccard_ioaddr;
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
@@ -268,6 +272,43 @@
}
dev->irq = pdev->irq;
+ /* bjoern: We need to tell the card to enable interrupts, in
+ case the serial eprom didn't do this already. See the
+ PLX9052 data book, p8-1 and 8-24 for reference. */
+ csr_reg = inl(plx_addr + PLX_INTCSR);
+ if (!(csr_reg & PLX_INTCSR_INTEN)) {
+ csr_reg |= PLX_INTCSR_INTEN;
+ outl(csr_reg, plx_addr + PLX_INTCSR);
+ csr_reg = inl(plx_addr + PLX_INTCSR);
+ if (!(csr_reg & PLX_INTCSR_INTEN)) {
+ printk(KERN_ERR PFX "Cannot enable interrupts\n");
+ goto fail;
+ }
+ }
+
+ err = orinoco_plx_cor_reset(priv);
+ if (err) {
+ printk(KERN_ERR PFX "Initial reset failed\n");
+ goto fail;
+ }
+
+ printk(KERN_DEBUG PFX "CIS: ");
+ for (i = 0; i < 16; i++) {
+ printk("%02X:", readb(attr_mem + 2*i));
+ }
+ printk("\n");
+
+ /* Verify whether a supported PC card is present */
+ /* FIXME: we probably need to be smarted about this */
+ for (i = 0; i < sizeof(cis_magic); i++) {
+ if (cis_magic[i] != readb(attr_mem +2*i)) {
+ printk(KERN_ERR PFX "The CIS value of Prism2 PC "
+ "card is unexpected\n");
+ err = -EIO;
+ goto fail;
+ }
+ }
+
err = register_netdev(dev);
if (err) {
printk(KERN_ERR PFX "Cannot register network device\n");
@@ -277,13 +318,21 @@
return 0;
fail:
- free_irq(dev->irq, dev);
+ free_irq(pdev->irq, dev);
+
fail_irq:
+ pci_set_drvdata(pdev, NULL);
free_orinocodev(dev);
+
fail_alloc:
pci_iounmap(pdev, mem);
- fail_map:
- release_region(pccard_ioaddr, pccard_iolen);
+
+ fail_map_io:
+ iounmap(attr_mem);
+
+ fail_map_attr:
+ pci_release_regions(pdev);
+
fail_resources:
pci_disable_device(pdev);
@@ -294,20 +343,18 @@
{
struct net_device *dev = pci_get_drvdata(pdev);
struct orinoco_private *priv = netdev_priv(dev);
+ struct orinoco_plx_card *card = priv->card;
+ u8 __iomem *attr_mem = card->attr_mem;
- unregister_netdev(dev);
-
- if (dev->irq)
- free_irq(dev->irq, dev);
+ BUG_ON(! dev);
- pci_iounmap(pdev, priv->hw.iobase);
-
+ unregister_netdev(dev);
+ free_irq(dev->irq, dev);
pci_set_drvdata(pdev, NULL);
-
free_orinocodev(dev);
-
- release_region(pci_resource_start(pdev, 3), pci_resource_len(pdev, 3));
-
+ pci_iounmap(pdev, priv->hw.iobase);
+ iounmap(attr_mem);
+ pci_release_regions(pdev);
pci_disable_device(pdev);
}
Index: working-2.6/drivers/net/wireless/orinoco_tmd.c
===================================================================
--- working-2.6.orig/drivers/net/wireless/orinoco_tmd.c 2005-01-12
15:47:48.216477768 +1100
+++ working-2.6/drivers/net/wireless/orinoco_tmd.c 2004-11-05
14:37:35.000000000 +1100
@@ -79,59 +79,89 @@
#include "orinoco.h"
#define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA) /* Enable PC card with
interrupt in level trigger */
+#define COR_RESET (0x80) /* reset bit in the COR register */
+#define TMD_RESET_TIME (500) /* milliseconds */
+
+/* Orinoco TMD specific data */
+struct orinoco_tmd_card {
+ u32 tmd_io;
+};
+
+
+/*
+ * Do a soft reset of the card using the Configuration Option Register
+ */
+static int orinoco_tmd_cor_reset(struct orinoco_private *priv)
+{
+ hermes_t *hw = &priv->hw;
+ struct orinoco_tmd_card *card = priv->card;
+ u32 addr = card->tmd_io;
+ unsigned long timeout;
+ u16 reg;
+
+ outb(COR_VALUE | COR_RESET, addr);
+ mdelay(1);
+
+ outb(COR_VALUE, addr);
+ mdelay(1);
+
+ /* Just in case, wait more until the card is no longer busy */
+ timeout = jiffies + (TMD_RESET_TIME * HZ / 1000);
+ reg = hermes_read_regn(hw, CMD);
+ while (time_before(jiffies, timeout) && (reg & HERMES_CMD_BUSY)) {
+ mdelay(1);
+ reg = hermes_read_regn(hw, CMD);
+ }
+
+ /* Did we timeout ? */
+ if (reg & HERMES_CMD_BUSY) {
+ printk(KERN_ERR PFX "Busy timeout\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
static int orinoco_tmd_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
int err = 0;
- u32 reg, addr;
struct orinoco_private *priv = NULL;
- unsigned long pccard_ioaddr = 0;
- unsigned long pccard_iolen = 0;
+ struct orinoco_tmd_card *card;
struct net_device *dev = NULL;
void __iomem *mem;
err = pci_enable_device(pdev);
if (err) {
printk(KERN_ERR PFX "Cannot enable PCI device\n");
- return -EIO;
+ return err;
}
- printk(KERN_DEBUG PFX "TMD setup\n");
- pccard_ioaddr = pci_resource_start(pdev, 2);
- pccard_iolen = pci_resource_len(pdev, 2);
- if (! request_region(pccard_ioaddr, pccard_iolen, DRIVER_NAME)) {
- printk(KERN_ERR PFX "I/O resource at 0x%lx len 0x%lx busy\n",
- pccard_ioaddr, pccard_iolen);
- err = -EBUSY;
- goto out;
+ err = pci_request_regions(pdev, DRIVER_NAME);
+ if (err != 0) {
+ printk(KERN_ERR PFX "Cannot obtain PCI resources\n");
+ goto fail_resources;
}
- addr = pci_resource_start(pdev, 1);
- outb(COR_VALUE, addr);
- mdelay(1);
- reg = inb(addr);
- if (reg != COR_VALUE) {
- printk(KERN_ERR PFX "Error setting TMD COR values %x should be
%x\n", reg, COR_VALUE);
- err = -EIO;
- goto out2;
+
+ mem = pci_iomap(pdev, 2, 0);
+ if (! mem) {
+ err = -ENOMEM;
+ goto fail_iomap;
}
/* Allocate network device */
- dev = alloc_orinocodev(0, NULL);
+ dev = alloc_orinocodev(sizeof(*card), orinoco_tmd_cor_reset);
if (! dev) {
printk(KERN_ERR PFX "Cannot allocate network device\n");
err = -ENOMEM;
- goto out2;
- }
-
- mem = pci_iomap(pdev, 2, 0);
- if (!mem) {
- err = -ENOMEM;
- goto out3;
+ goto fail_alloc;
}
priv = netdev_priv(dev);
- dev->base_addr = pccard_ioaddr;
+ card = priv->card;
+ card->tmd_io = pci_resource_start(pdev, 1);
+ dev->base_addr = pci_resource_start(pdev, 2);
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
@@ -140,36 +170,46 @@
printk(KERN_DEBUG PFX "Detected Orinoco/Prism2 TMD device "
"at %s irq:%d, io addr:0x%lx\n", pci_name(pdev), pdev->irq,
- pccard_ioaddr);
+ dev->base_addr);
err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ,
dev->name, dev);
if (err) {
printk(KERN_ERR PFX "Cannot allocate IRQ %d\n", pdev->irq);
err = -EBUSY;
- goto out4;
+ goto fail_irq;
}
dev->irq = pdev->irq;
+ err = orinoco_tmd_cor_reset(priv);
+ if (err) {
+ printk(KERN_ERR PFX "Initial reset failed\n");
+ goto fail;
+ }
+
err = register_netdev(dev);
if (err) {
printk(KERN_ERR PFX "Cannot register network device\n");
- goto out5;
+ goto fail;
}
return 0;
-out5:
- free_irq(dev->irq, dev);
-out4:
- pci_iounmap(pdev, mem);
-out3:
+ fail:
+ free_irq(pdev->irq, dev);
+
+ fail_irq:
+ pci_set_drvdata(pdev, NULL);
free_orinocodev(dev);
-out2:
- release_region(pccard_ioaddr, pccard_iolen);
-out:
+
+ fail_alloc:
+ pci_iounmap(pdev, mem);
+
+ fail_iomap:
+ pci_release_regions(pdev);
+
+ fail_resources:
pci_disable_device(pdev);
- printk(KERN_DEBUG PFX "init_one(), FAIL!\n");
return err;
}
@@ -177,21 +217,16 @@
static void __devexit orinoco_tmd_remove_one(struct pci_dev *pdev)
{
struct net_device *dev = pci_get_drvdata(pdev);
- struct orinoco_private *priv = netdev_priv(dev);
+ struct orinoco_private *priv = dev->priv;
- unregister_netdev(dev);
-
- if (dev->irq)
- free_irq(dev->irq, dev);
-
- pci_iounmap(pdev, priv->hw.iobase);
+ BUG_ON(! dev);
+ unregister_netdev(dev);
+ free_irq(dev->irq, dev);
pci_set_drvdata(pdev, NULL);
-
free_orinocodev(dev);
-
- release_region(pci_resource_start(pdev, 2), pci_resource_len(pdev, 2));
-
+ pci_iounmap(pdev, priv->hw.iobase);
+ pci_release_regions(pdev);
pci_disable_device(pdev);
}
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist. NOT _the_ _other_ _way_
| _around_!
http://www.ozlabs.org/people/dgibson
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click
|
