--- Begin Message ---
|
Subject: |
Re: [Orinoco-devel] Networking "stops" with .15rc1 |
Pavel Roskin wrote:
On Fri, 7 May 2004, Stephen R. Bordeleau wrote:
I appologize if this has been posted before but today I downloaded and
installed the orinoco 0.15rc1 driver and networking seems to "stop"
working after a short time.
Specifically, when I have the driver installed, I'll be browsing web
pages or going on irc etc. and I'll still see good signal strength with
the meters on gkrellm however shortly thereafter I stop getting any data
to my card from the internet ie. on gkrellm my eth1 will show absolutely
no activity yet everything else looks to be fine. If i do ifdown and
ifup for eth0 it'll work until I get to this point. From there, if I try
ifup eth1 it just fails. This doesn't happen with the stock driver from
selinux-2.6.5 though so I'm assuming it's an issue with .15rc1. If you
have any insight, I'd love to hear it.
It looks more like a routing problem than a problem with the drivers.
Bringing eth0 down and up should not affect the driver for eth1, but it
can rearrange the routes in the routing table.
Please try to reproduce the problem to just one card, the one that uses
the Orinoco driver. When the problem happens, please make sure that the
network settings are still correct (see "route" and "ifconfig" output).
Also run "iwconfig" to see if the card is still associated.
Please post the kernel log (it's printed by the "dmesg" command). In
particular, I'm interested to see the messages from the driver when it
initializes the hardware and when you experience the problem. Also please
post the "iwconfig" output.
Attached is the full dmesg, might give you a better idea of what's going
on.
It's very unstable for me so far but maybe you will have better insight.
Thanks,
Steve
tting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 26 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 25 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 33 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 25 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 23 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 25 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 23 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 25 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 23 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 25 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 23 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 25 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
printk: 23 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
eth1: Error -19 setting MAC address
eth1: Error -19 configuring card
orinoco_lock() called with hw_unavailable (dev=cf0c3800)
dev_mc_discard: multicast leakage! dmi_users=1
dev_mc_discard: multicast leakage! dmi_users=1
dev_mc_discard: multicast leakage! dmi_users=1
dev_mc_discard: multicast leakage! dmi_users=1
orinoco 0.15rc1STA (David Gibson
<hermes-xT8FGy+AXnRB3Ne2BGzF6laj5H9X9Tb+@xxxxxxxxxxxxxxxx>, Pavel Roskin
<proski-mXXj517/zsQ@xxxxxxxxxxxxxxxx>, et al)
orinoco_cs 0.15rc1STA (David Gibson
<hermes-xT8FGy+AXnRB3Ne2BGzF6laj5H9X9Tb+@xxxxxxxxxxxxxxxx>, Pavel Roskin
<proski-mXXj517/zsQ@xxxxxxxxxxxxxxxx>, et al)
eth1: Hardware identity 0001:0004:0005:0000
eth1: Station identity 001f:0001:0008:0048
eth1: Firmware determined as Lucent/Agere 8.72
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:2D:BE:B1:E0
eth1: Station name "HERMES I"
eth1: ready
eth1: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x013f
eth1: New link status: Connected (0001)
eth1: no IPv6 routers present
IPKF INPUT Catch-all: IN=eth1 OUT= MAC= SRC=10.0.1.3 DST=255.255.255.255
LEN=136 TOS=0x00 PREC=0x00 TTL=64 ID=3 DF PROTO=UDP SPT=513 DPT=513 LEN=116
IPKF New Not SYN: IN=eth1 OUT= MAC=00:02:2d:be:b1:e0:00:03:93:e4:af:4a:08:00
SRC=213.218.8.228 DST=10.0.1.3 LEN=74 TOS=0x00 PREC=0x00 TTL=52 ID=34133 DF
PROTO=TCP SPT=110 DPT=32782 WINDOW=5840 RES=0x00 ACK PSH FIN URGP=0
IPKF New Not SYN: IN=eth1 OUT= MAC=00:02:2d:be:b1:e0:00:03:93:e4:af:4a:08:00
SRC=213.218.8.228 DST=10.0.1.3 LEN=74 TOS=0x00 PREC=0x00 TTL=52 ID=34134 DF
PROTO=TCP SPT=110 DPT=32782 WINDOW=5840 RES=0x00 ACK PSH FIN URGP=0
IPKF New Not SYN: IN=eth1 OUT= MAC=00:02:2d:be:b1:e0:00:03:93:e4:af:4a:08:00
SRC=213.218.8.228 DST=10.0.1.3 LEN=74 TOS=0x00 PREC=0x00 TTL=52 ID=34135 DF
PROTO=TCP SPT=110 DPT=32782 WINDOW=5840 RES=0x00 ACK PSH FIN URGP=0
eth1: New link status: Disconnected (0002)
eth1: New link status: Connected (0001)
IPKF INPUT Catch-all: IN=eth1 OUT= MAC= SRC=10.0.1.3 DST=255.255.255.255
LEN=136 TOS=0x00 PREC=0x00 TTL=64 ID=4 DF PROTO=UDP SPT=513 DPT=513 LEN=116
IPKF New Not SYN: IN=eth1 OUT= MAC=00:02:2d:be:b1:e0:00:03:93:e4:af:4a:08:00
SRC=213.218.8.228 DST=10.0.1.3 LEN=74 TOS=0x00 PREC=0x00 TTL=52 ID=34136 DF
PROTO=TCP SPT=110 DPT=32782 WINDOW=5840 RES=0x00 ACK PSH FIN URGP=0
IPKF INPUT Catch-all: IN=eth1 OUT= MAC= SRC=10.0.1.3 DST=10.0.1.255 LEN=44
TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32920 DPT=7741 LEN=24
IPKF INPUT Catch-all: IN=eth1 OUT= MAC= SRC=10.0.1.3 DST=10.0.1.255 LEN=78
TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32920 DPT=137 LEN=58
IPKF INPUT Catch-all: IN=eth1 OUT= MAC= SRC=10.0.1.3 DST=10.0.1.255 LEN=78
TOS=0x00 PREC=0x00 TTL=64 ID=1 DF PROTO=UDP SPT=32920 DPT=137 LEN=58
IPKF INPUT Catch-all: IN=eth1 OUT= MAC= SRC=10.0.1.3 DST=10.0.1.255 LEN=78
TOS=0x00 PREC=0x00 TTL=64 ID=2 DF PROTO=UDP SPT=32920 DPT=137 LEN=58
IPKF Invalid TCP flag: IN=eth1 OUT=
MAC=00:02:2d:be:b1:e0:00:03:93:e4:af:4a:08:00 SRC=10.0.1.1 DST=10.0.1.3 LEN=28
TOS=0x00 PREC=0x00 TTL=64 ID=25650 DF PROTO=ICMP TYPE=0 CODE=0 ID=33806 SEQ=0
IPKF Invalid TCP flag: IN=eth1 OUT=
MAC=00:02:2d:be:b1:e0:00:03:93:e4:af:4a:08:00 SRC=10.0.1.1 DST=10.0.1.3 LEN=28
TOS=0x00 PREC=0x00 TTL=64 ID=25652 DF PROTO=ICMP TYPE=0 CODE=0 ID=33806 SEQ=0
IPKF Invalid TCP flag: IN=eth1 OUT=
MAC=00:02:2d:be:b1:e0:00:30:65:26:ab:a4:08:00 SRC=10.0.1.2 DST=10.0.1.3 LEN=28
TOS=0x00 PREC=0x00 TTL=64 ID=45694 DF PROTO=ICMP TYPE=0 CODE=0 ID=33806 SEQ=0
orinoco_lock() called with hw_unavailable (dev=cf0c3800)
orinoco 0.15rc1STA (David Gibson
<hermes-xT8FGy+AXnRB3Ne2BGzF6laj5H9X9Tb+@xxxxxxxxxxxxxxxx>, Pavel Roskin
<proski-mXXj517/zsQ@xxxxxxxxxxxxxxxx>, et al)
orinoco_cs 0.15rc1STA (David Gibson
<hermes-xT8FGy+AXnRB3Ne2BGzF6laj5H9X9Tb+@xxxxxxxxxxxxxxxx>, Pavel Roskin
<proski-mXXj517/zsQ@xxxxxxxxxxxxxxxx>, et al)
eth1: Hardware identity 0001:0004:0005:0000
eth1: Station identity 001f:0001:0008:0048
eth1: Firmware determined as Lucent/Agere 8.72
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:2D:BE:B1:E0
eth1: Station name "HERMES I"
eth1: ready
eth1: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x013f
eth1: New link status: Connected (0001)
eth1: no IPv6 routers present
IPKF INPUT Catch-all: IN=eth1 OUT= MAC= SRC=10.0.1.3 DST=255.255.255.255
LEN=136 TOS=0x00 PREC=0x00 TTL=64 ID=5 DF PROTO=UDP SPT=513 DPT=513 LEN=116
IPKF New Not SYN: IN=eth1 OUT= MAC=00:02:2d:be:b1:e0:00:03:93:e4:af:4a:08:00
SRC=213.218.8.228 DST=10.0.1.3 LEN=74 TOS=0x00 PREC=0x00 TTL=52 ID=56870 DF
PROTO=TCP SPT=110 DPT=32792 WINDOW=5840 RES=0x00 ACK PSH FIN URGP=0
IPKF New Not SYN: IN=eth1 OUT= MAC=00:02:2d:be:b1:e0:00:03:93:e4:af:4a:08:00
SRC=213.218.8.228 DST=10.0.1.3 LEN=74 TOS=0x00 PREC=0x00 TTL=52 ID=56871 DF
PROTO=TCP SPT=110 DPT=32792 WINDOW=5840 RES=0x00 ACK PSH FIN URGP=0
IPKF New Not SYN: IN=eth1 OUT= MAC=00:02:2d:be:b1:e0:00:03:93:e4:af:4a:08:00
SRC=213.218.8.228 DST=10.0.1.3 LEN=74 TOS=0x00 PREC=0x00 TTL=52 ID=56872 DF
PROTO=TCP SPT=110 DPT=32792 WINDOW=5840 RES=0x00 ACK PSH FIN URGP=0
IPKF INPUT Catch-all: IN=eth1 OUT= MAC= SRC=10.0.1.3 DST=255.255.255.255
LEN=136 TOS=0x00 PREC=0x00 TTL=64 ID=6 DF PROTO=UDP SPT=513 DPT=513 LEN=116
IPKF New Not SYN: IN=eth1 OUT= MAC=00:02:2d:be:b1:e0:00:03:93:e4:af:4a:08:00
SRC=213.218.8.228 DST=10.0.1.3 LEN=74 TOS=0x00 PREC=0x00 TTL=52 ID=56873 DF
PROTO=TCP SPT=110 DPT=32792 WINDOW=5840 RES=0x00 ACK PSH FIN URGP=0
eth1: New link status: Connected (0001)
eth1: no IPv6 routers present
IPKF INPUT Catch-all: IN=eth1 OUT= MAC= SRC=10.0.1.3 DST=255.255.255.255
LEN=136 TOS=0x00 PREC=0x00 TTL=64 ID=7 DF PROTO=UDP SPT=513 DPT=513 LEN=116
eth1: New link status: Disconnected (0002)
eth1: New link status: Connected (0001)
device eth1 entered promiscuous mode
hermes @ IO 0x100: Card removed while waiting for command completion.
hermes @ IO 0x100: Card removed while waiting for command completion.
printk: 14 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
hermes @ IO 0x100: Card removed while issuing command.
hermes @ IO 0x100: Card removed while issuing command.
hermes @ IO 0x100: Card removed while issuing command.
hermes @ IO 0x100: Card removed while issuing command.
hermes @ IO 0x100: Card removed while issuing command.
hermes @ IO 0x100: Card removed while issuing command.
hermes @ IO 0x100: Card removed while issuing command.
hermes @ IO 0x100: Card removed while issuing command.
hermes @ IO 0x100: Card removed while issuing command.
printk: 36 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 45 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 45 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 45 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 44 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 45 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 45 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 45 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 44 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 45 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 45 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 45 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 43 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 44 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
eth1: Error -19 setting PROMISCUOUSMODE to 1.
eth1: Error -19 setting multicast list.
device eth1 entered promiscuous mode
printk: 31 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 20 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 18 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
IPKF INPUT Catch-all: IN=eth1 OUT= MAC= SRC=10.0.1.3 DST=255.255.255.255
LEN=160 TOS=0x00 PREC=0x00 TTL=64 ID=8 DF PROTO=UDP SPT=513 DPT=513 LEN=140
printk: 20 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 18 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 20 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 18 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 20 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 18 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 20 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 18 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
printk: 20 messages suppressed.
hermes @ IO 0x100: Card removed while issuing command.
smime.p7s
Description: S/MIME Cryptographic Signature
--- End Message ---
