|
osdir.com mailing list archive |
|
Subject: vctc link not working on 2.4.19 under VM - msg#00005List: debian.ports.s390Greetings; I can't get my ctc link to work. As far as I can see everything is setup as it should be but I can't talk to either my VM stack, or through it to either of my other two linux guests. One of them is a Marist distrib, and the other is a TurboLinux. All the routes are "the same" and the other two can talk just fine. Just can't figure this one out. BTW, I upgraded from the 2.4.17 kernel, and the link through my OSA card is working just fine! Many TIA! Dennis Thread at a glance:
Previous Message by Date: click to view message previewarts build failureCan whoever happens to maintain the s390 buildd check the config.log of arts package to see why it fails to find the xlibs-dev files. It built fine on arm so I have no idea why it would be failing on s390. Please cc: on response. Thanks, Chris Cheney Next Message by Date: click to view message previewvctc link not working on 2.4.19 under VM - followupGreetings again; I rebooted and now neither link, eth0 or ctc0, is activated at boot. I can bring up the ctc by hand, setup the routes, and wonder of wonders, it works! However, if I try to do anything to the eth link I get the following. ifconfig eth0 Starting lcs module $Revision: 1.132 $ $Date: 2002/04/30 19:13:38 $ with chandev support,with multicast support, with ethernet support, with token ring support. debug: lcs: new level 0 drvr globals not in list 01c8b000 lcs_probe kmalloc failed No lcs capable cards found Terminating lcs module. eth0: error fetching interface information: Device not found -arsenic:~-# 00: 00: CP Q OSA 00: OSA 070E ON OSA 070E SUBCHANNEL = 0000 00: OSA 070F ON OSA 070F SUBCHANNEL = 0001 I changed my /etc/network/interfaces file and here it is iface eth0 inet static address 10.80.20.33 netmask 255.0.0.0 network 10.0.0.0 broadcast 10.255.255.255 up ifconfig eth0 mtu 1492 gateway 10.80.20.1 # The second network card - this entry was created by hand iface ctc0 inet static address 192.168.150.33 netmask 255.255.255.0 network 192.168.150.0 pointopoint 192.168.150.31 up ifconfig ctc0 mtu 1492 up route add -net 192.168.150.0 netmask 255.255.255.0 gw 192.168.150.31 gateway 192.168.150.31 Hope this helps! Many TIA, Dennis -- Dennis G. Wicks Systems Programmer dennisw@xxxxxx Communications Data Group Tel: (217)355-7117 Fax: (217)351-6994 102 S. Duncan Rd. Champaign, IL 61822 Previous Message by Thread: click to view message previewarts build failureCan whoever happens to maintain the s390 buildd check the config.log of arts package to see why it fails to find the xlibs-dev files. It built fine on arm so I have no idea why it would be failing on s390. Please cc: on response. Thanks, Chris Cheney Next Message by Thread: click to view message previewvctc link not working on 2.4.19 under VM - followupGreetings again; I rebooted and now neither link, eth0 or ctc0, is activated at boot. I can bring up the ctc by hand, setup the routes, and wonder of wonders, it works! However, if I try to do anything to the eth link I get the following. ifconfig eth0 Starting lcs module $Revision: 1.132 $ $Date: 2002/04/30 19:13:38 $ with chandev support,with multicast support, with ethernet support, with token ring support. debug: lcs: new level 0 drvr globals not in list 01c8b000 lcs_probe kmalloc failed No lcs capable cards found Terminating lcs module. eth0: error fetching interface information: Device not found -arsenic:~-# 00: 00: CP Q OSA 00: OSA 070E ON OSA 070E SUBCHANNEL = 0000 00: OSA 070F ON OSA 070F SUBCHANNEL = 0001 I changed my /etc/network/interfaces file and here it is iface eth0 inet static address 10.80.20.33 netmask 255.0.0.0 network 10.0.0.0 broadcast 10.255.255.255 up ifconfig eth0 mtu 1492 gateway 10.80.20.1 # The second network card - this entry was created by hand iface ctc0 inet static address 192.168.150.33 netmask 255.255.255.0 network 192.168.150.0 pointopoint 192.168.150.31 up ifconfig ctc0 mtu 1492 up route add -net 192.168.150.0 netmask 255.255.255.0 gw 192.168.150.31 gateway 192.168.150.31 Hope this helps! Many TIA, Dennis -- Dennis G. Wicks Systems Programmer dennisw@xxxxxx Communications Data Group Tel: (217)355-7117 Fax: (217)351-6994 102 S. Duncan Rd. Champaign, IL 61822 Loading Comments...
|
|
