Re: Screen window position with Tame

Thanks for confirming it was Tame 5.0 and not me at fault with the DP window positioning problem although my font type & size did seem to stick.

Michael


Colin Roberts wrote:

Sorry for coming in here late but I can confirm I had similar experience with ver 5.0 as well, when it was 1st released - lots of bells and whistles but I couldn't find a way to get window positioning, font type & size, and lots of other goodies to stick either,  So I also went back to 4.5. As I can have up to 10 dps running at one time I prefer to let the system position the window so most are visible with a sort of cascade effect. Unfortunately Tame was also unresponsive to any queries raised then - which must be a least a couple of years ago now.

Ver 4.5 is working fine apart from one dos program that intermittently loses the cursor (and for which I think tame is the culprit) but the cursor problem has never been an issue with DP and we'd be totally snookered without it.

 

Colin Roberts

----- Original Message -----

From: Michael Iannantuoni

To: Dataperfect Users Discussion Group

Sent: Wednesday, 7 November 2007 05:21

Subject: Re: [Dataperf] Screen window position with Tame

Thanks Don,

I have downloaded and am now using version 4.5 too. It doesn't have quite so many options as version 5 but I don't really need anything fancy, it just works!

Michael

Don Codling wrote:

November 6, 2007

Hi Michael:

I'm still using TAME version 4.5. All I did was install TAME and ignore it. There is nothing in my Autoexec.bat or Config.sys files.  TAME has added itself to autoexec.nt.  It runs when I open DP - it probably slows the opening by half a second, and I have no problems.  When I click that top left icon, the upper part of the menu is as you report. Then I get a lower part, Close, edit, defaults, properties, hide mouse pointer.  That properties choice lets me choose a clear crisp font & size for DP, get the maximum possible use of my screen for a full view of DP in a window, position the DP window, etc.

Don Codling
WP 12.0.0.602
DP 2.6x
Windows XP home, SP2
512 MBytes RAM

Michael Iannantuoni wrote:

Hi Don,

When I click the icon at the top left corner of the DP window, "properties" is not a menu option. What I see, other than the standard Windows DOS box options of Restore (greyed out), Move, Size, Minimize & Maximize, are various Tame options of Edit, View, Help, Tame Settings Files, Troubleshooting - all these have sub menus but nowhere do I see anything about window position. I think this is because I let Tame load at Windows start-up rather than as part of a batch file to run my DP application.

I will try the batch file approach and report back.

Thanks for your help,

Michael


Don Codling wrote:

November 5, 2007

Michael, since nobody else has offered a solution, let me try.

I do not use TAME at all for the purpose of positioning DP (I do use TAME). To set the position (& fonts & window size), I click the icon at the top left corner of the DP window, & choose "properties" from the menu.

Window position & theoretical size is set in the layout tab. I choose screen buffer size & layout size 80 x 25.  That gives me a maximum DP screen, so far as I can tell. (The actual size of the window is set by adjusting the font on the font tab.)

Then I set the position in the Window position section - I choose 0,0 for the top left corner of my screen, but you can adjust it as you want it.  Be sure that you have unchecked "Let system position window".

Click OK, & then choose "Save properties for future windows with the same title".  That means it affects all DP databases, & retains the settings you have used.
Click OK again & you have it.

Hope this works for you as well as it does for me.

Don Codling
WP 12.0.0.602
DP 2.6x
Windows XP home, SP2
512 MBytes RAM

Michael Iannantuoni wrote:

I have tried asking this to support-qxEgrAMnuSBBDgjK7y7TUQ@xxxxxxxxxxxxxxxx but it bounced back two days later.

Does anyone have a good knowledge please of Tame: I have Tame 5 running on a Windows XP Pro system and despite removing the ";*" from the line "AutoSaveSettings=on  ; Save view settings and use on next run" in "_ProcessStartup.init.tam", my  DP applications do not remember the position of their window between sessions. What am I doing wrong please?

Michael

------------------------------------------------------------------------

_______________________________________________
Dataperf mailing list
Dataperf-Ii8YPGKeNuMyuW1uK6fEew@xxxxxxxxxxxxxxxx
http://lists.dataperfect.nl/mailman/listinfo/dataperf
 

_______________________________________________
Dataperf mailing list
Dataperf-Ii8YPGKeNuMyuW1uK6fEew@xxxxxxxxxxxxxxxx
http://lists.dataperfect.nl/mailman/listinfo/dataperf

------------------------------------------------------------------------

_______________________________________________
Dataperf mailing list
Dataperf-Ii8YPGKeNuMyuW1uK6fEew@xxxxxxxxxxxxxxxx
http://lists.dataperfect.nl/mailman/listinfo/dataperf
 

_______________________________________________
Dataperf mailing list
Dataperf-Ii8YPGKeNuMyuW1uK6fEew@xxxxxxxxxxxxxxxx
http://lists.dataperfect.nl/mailman/listinfo/dataperf

---

_______________________________________________
Dataperf mailing list
Dataperf-Ii8YPGKeNuMyuW1uK6fEew@xxxxxxxxxxxxxxxx
http://lists.dataperfect.nl/mailman/listinfo/dataperf

_______________________________________________
Dataperf mailing list
Dataperf-Ii8YPGKeNuMyuW1uK6fEew@xxxxxxxxxxxxxxxx
http://lists.dataperfect.nl/mailman/listinfo/dataperf
  

_______________________________________________
Dataperf mailing list
Dataperf-Ii8YPGKeNuMyuW1uK6fEew@xxxxxxxxxxxxxxxx
http://lists.dataperfect.nl/mailman/listinfo/dataperf